How to choose a best furnace

Central heating system provides warmth to the whole interior of a building. A central heating system has a primary heating appliance such as a furnace or boiler located in an out-of-the-way place such as a basement or garage.

A furnace works by blowing heated air through system of air ducts that deliver the warm air to room radiators or convectors. Obviously, furnace is one of the best important equipment in heating system. How to choose a best furnace?

Size

The furnaces in most homes are larger than necessary. You will waste money on buying a bigger one and waste energy in operating it. A  too large furnace will cycle on and off more frequently. It might cause the temperature to vary uncomfortably. Also, a large replacement furnace might require larger ducts. Without the right size ducts, airflow can be noisy.

Nevertheless, a too small furnace won’t keep your house comfortable. Therefore, the furnace’s specifications should fit your needs.

Choose a reputable contractor such as Acs Absolute Comfort heating and cooling service in Texas to ensure your furnace is installed properly and correct sizing. Furthermore, the furnace is installed, maintained it regularly according to the manufacturer’s recommendations for Air conditioning AC HVAC service in Missouri city Texas.

Efficient

Most of new central heating systems currently use gas. The price of a furnace generally rises in step with its fuel efficiency. A furnace with a 90 % AFUE(annual fuel utilization efficiency is a thermal efficiency measure of combustion equipment like furnaces, boilers, and water heaters- According wikipedia.org) might cost $1,000 more than a similar size unit with an 80 % AFUE. Initial cost of 90 % AFUE is higher, however, you can recoup that additional cost through lower energy bills over the life of furnace. In addition, the climate, insulation of your house, and the rate of your local energy also affect your decision.

As you decide, insist the contractor can consult you to select models in range of efficiencies and calculate the annual estimated operating cost of furnace which you are considering.

Several ways to reduce energy bills, refer in these articles: Simple ways to lower your energy bills – Save on water heating, Simple ways to lower your energy bills – Saving on lighting, Simple ways to lower your energy bills – Save on Air conditioning, Simple ways to lower your energy bills – Save on other appliances and electronics and  Tips save energy on heating system

How to lower your monthly utility bills

Maintain HVAC

If you have an HVAC system, you have to make sure to change the air filter regularly. This will improve the efficiency of your machine and lower your running cost as well. Check your user’s manual to know at which frequency you’re supposed to change the filter.  

 

Caulk leaks

Make sure to caulk and weather strip your window and door frames to plug any air leaks. This will improve your house’s energy efficiency up to 20%.

 

Update your appliances to newer models

Update your appliances to newer energy efficient models that have the Energy Star logo. You’ll save a bunch on you monthly bills. A typical example of this is to buy a front loading washing machine. Not only does it use less water, but it’s more efficient in its energy use.

Speaking about washing machines, make sure you do your laundry using cold water. Also, make sure you run full loads. So instead of doing multiple small loads, do one big load.

 

Adjust temperature

So another awesome way to save is to lower your temperature when you’re going to sleep at night. During the winter months, you want that temperature to be  about 63ᐤF or 17ᐤC. Many scientific reports have proven that keeping your body cool at night is conducive to good sleep. So that’s an added bonus. During those hot summer days, you can increase the ambient temperature to 72ᐤF  or 22ᐤC, so you’re not wasting your air conditioning’s energy cooling the house too much.

Air conditioning AC HVAC service in Katy Texas

Install programmable thermostats

Now another great way to cut costs is to buy programmable thermostats. So that way, during winter you can set it to lower the house’s temperature when you’re not at home. So those 8 to 10 hours that you’re not actually in your house you’ll be saving money because you’re not overly heating the house and wasting energy.

 

Change regular light bulbs

Change all your regular light bulbs which are incandescent to some compact fluorescent models or even better, LED. Now that will save you a bunch of money because for example, a standard 60W bulb can be replaced by the equivalent 13W compact fluorescent or greater yet, 9W LED equivalent. So you’re saving 4 to 6 times the energy. That will have a direct impact on your monthly bills.

Install timer

Put a timer on interior or exterior lights that you have the tendency to leave open for longer periods of time for security purposes. That way, when you go to sleep, they simply turn off and you don’t even have to think about it.

 

Keep water heater temperature to 120ᐤF

You can adjust your water heater temperature to 120ᐤF. It shouldn’t be hotter than that. Because one, it can cause scalding and second of all you’re just wasting energy. Doing this is pretty simple, you just cut off the power to the water heater, you pop open the panels with a screwdriver, and you adjust the needle to 120ᐤF. Put the panel back on, turn the power on, and you’re good to go.

 

Unplug unused devices

Your electronics using energy when they’re not in use. To remedy this, you can unplug the unused electronic devices, or turn off the power switch.

Air conditioning AC HVAC service in Pearland Texas

More article:  The best most efficient energy source for heating system

The best most efficient energy source for heating system

If you have an electric baseboard heat with basically the lab equipment at all. You just use electricity to heat your baseboard, it’s easy cheap but you spend a lot of money and electricity every month. If you have a fourth hot water baseboard, it might look like an electrical baseboard but the difference is it uses hot water instead of the electrical resistance. So which means you have a boiler in your basement, it burns all your gas to heat up the water and do the heat. This is a much more efficient way to heat your home but not the best. If you have warm air coming from the floor wall or ceiling, that means you have a ductwork. You have a central warm air system, you have a furnace that burns oil or gas and circulates the warm air throughout the house to do your heating with the right upgrades. The system can control our only temperature but the humidity and the quality of the air inside your home making the kind of the best system, Fast AC service in Richmond Texas

If you need a trusted heating and air conditioning consultant new upgrade, installations, service and repair please call us at (+1) 281 495 2013.

https://heatingairconditioningintexas.wordpress.com/2017/06/09/recommended-thermostat-settings-for-home-comfort/

Recommended Thermostat Settings for Home Comfort

Ones home’s living room cooling and heating process ought to furnish benefits together with convenience for a interior natural environment. Today, several people are worried reducing their energy bills, nevertheless having that convenience they really want in your house.

Air conditioning AC HVAC service in Sugar Land Texas

Fast Air conditioning AC HVAC service in Richmond Texas

One particular resolution for taking care of your heating and cooling systems may be to adjust thermostat options, consistent with your routines.

In the summer, it is generally recommended that you should set the thermostat to 78 ºF when you’re home and 85ºF when away from home. You may save around 6 to 8 percentage off of your electrical power charge, for each degree.

In the winter, keeping your thermostat at 68ºF when you are at home to reduce your energy bill 5 to 15 percent per year.

One good idea is usually reducing that thermostat during the night time whenever you sleeping.

Many people like sleeping in a cooler environment while using winter blankets to warm. However, the humidity affects to evaporation of moisture from the skin. Read here about this.

Installing a programmable thermostat will help you automatically adjust the temperature up to six or more times per day with a scheduled heating and cooling program.

While you are sleeping or at your workplace, the programmable thermostat set temperature lower to make a difference in your energy bills.  

Website: http://acscomfort.com

Other articles: https://heatingairconditioningintexas.wordpress.com/2017/05/24/heating-and-cooling-repair-do-it-yourself/

HEATING AND COOLING Repair : Do-it-yourself

Your heating system is blowing cold air or your cooling is system blowing hot air.

This room is fuel hotter or colder than another. Since  your system is constantly running but nothing seems to be happening. If so I have some information that could help your system get back to producing comfortable air. These are the seven helpful steps you can take:

Step 1: Check your thermostat setting

Make sure it’s properly set to either heat or cool. Replace the batteries on your  programmable thermostat. If heating set temperatures at least 10 degrees warmer than the indoor temperature. If cooling set at 10 degrees cooler. This will give you a better idea if your system is operating properly.

Step 2: Test your thermostat’s accuracy with another temperature gauge

If they don’t match, your thermostat may be out of calibration and needs to be reset. To do so reference the manufacturer’s instructions.

Step 3: Check the power to your unit

A circuit breaker may be tripped, in that case flip the switch, this should not happen often. If it does you should consult a licensed HVAC technician. Also check the master switches to both your inside and outside units to make sure both are on and receiving electricity.

Step 4: Press your ai conditioner’s reset button if it has one

By resetting the unit, it can clear some of the mirror mechanical issues that may cause the system to act irregularly.

Step 5: Go to the air conditioner return vent and change your filter

Dirty restricts air flow can cause problems and impact the temperature of your home as a rule of thumb change your filter every month

Step 6: Clear grass, weeds, anything that may be obstructing airflow, and clean your condensing unit with a commercial cold cleaner

It’s recommended that you do not open up the unit damage can easily be done to the fans and can drastically shorten the life of your system

Visit http://acscomfort.com/local/sugar-land-tx

Step 7: Make sure none of your air vents are blocked!

Ensure none of your air vents are blocked nothing should be obstructing them including drapes and furniture. They can restrict airflow and impact a room temperature

Those are my seven steps, you can take to repair your HVAC system. If your system still acts irregularly after following them, it likely needs servicing. Choose a heating and cooling systems company it’s important that you find one that employs licensed highly-trained historical professional for Same day Air conditioning AC HVAC service in Richmond Texas. 

https://heatingairconditioningintexas.wordpress.com/2017/03/30/hvac-repair-troubleshooting-tips-p-4/

How to Select the Best Window Air Conditioner

There is no need to suffer through summer heat when inexpensive, energy-efficient air conditioners are widely available. Since October 26, 2015, all ENERGY STAR rated room air conditioners have been required to meet a new standard, ENERGY STAR 4.0, that sets maximum power use at 10% less than older models following the 2014 guidelines. And, when used to provide cooling only where they’re needed, room air conditioners are less expensive to operate than central units. This guide will help you find the model that is right for you.

Energy efficiency of room air conditioners

A room air conditioner’s efficiency is measured by the energy efficiency ratio (EER). The EER is the ratio of the cooling capacity (in British thermal units [Btu] per hour) to the power input (in watts). The higher the EER rating, the more efficient the air conditioner. Each increase of 1.0 on the EER scale represents a 10% increase in energy efficiency.

When buying a new room air conditioner, information about the EER can be found on the EnergyGuide label for the unit. Look for an EER of at least 12 and the ENERGY STAR label. Earning the ENERGY STAR means a product meets strict energy efficiency guidelines set by the U.S. Environmental Protection Agency and the U.S. Department of Energy.

• ENERGY STAR 4.0 qualified room air conditioners use at least 10% less energy than conventional models. You can find a complete list here: https://www.energystar.gov/productfinder/product/certified-room-air-conditioners/
• ENERGY STAR 4.0 qualified room air conditioners often include timers for better temperature control, allowing you to use the minimum amount of energy you need to cool your room.

Properly Sizing a Room Air Conditioner

The required cooling capacity for a room air conditioner depends on the size of the room being cooled. Room air conditioners generally have cooling capacities that range from 5,500 Btu per hour to 14,000 Btu per hour.

Many people buy an air conditioner that is too large, thinking it will provide better cooling. However, an over-sized air conditioner is actually less effective — and wastes energy at the same time. Air conditioners remove both heat and humidity from the air. If the unit is too large, it will cool the room quickly, but only remove some of the humidity. This leaves the room with a damp, clammy feeling. A properly sized unit will remove humidity effectively as it cools.To figure out which size unit is best for your cooling needs, see the Air Conditioner Cooling Needs Calculator below.

Other factors to consider when buying

Verify that your home’s electrical system can meet the unit’s power requirements. Room units operate on 115-volt or 230-volt circuits. The standard household receptacle is a connection for a 115-volt branch circuit. Large room units rated at 115 volts may require a dedicated circuit and room units rated at 230 volts may require a special circuit. If you are mounting your air conditioner near the corner of a room, look for a unit that can direct its airflow in the desired direction for your room layout. If you need to mount the air conditioner at the narrow end of a long room, look for models that have a “turbo” fan mode that can drive air further into the room. Other features to look for:

• A filter that slides out easily for regular cleaning
• Logically arranged controls
• A digital readout for the thermostat setting, and
• A built-in timer.

Do you need a smart air conditioner?

For those that keep to a regular schedule and don’t have smart home devices installed in their home, a timer will help save money (about $100 on the air conditioner itself and your energy bill) and save you from coming home to a hot, stuffy home. For many, though, the ability to control a room air conditioner from anywhere can be a huge help and cost savings, especially if you don’t stick to a schedule. And, you can connect them to other smart home devices so they fit seamlessly into your daily routine.

Our Picks

Small rooms (up to 150 square feet)

The Frigidaire FFRE0533S1 ($167.99 on Amazon), rated at 5,000BTU, gets high marks for its cooling and dehumidification capabilities of up to 1.1 pints per hour. The unit, which has an EER of 12.2, two cooling and two fan speeds, a 24-hour programmable timer, built-in thermostat with digital temperature readout, remote control and a four-way adjustable vent to direct air flow.

Medium rooms (up to 350 square feet)

The Wi-Fi connected Frigidaire FGRC0844S1 Cool Connect ($296.99 on Amazon) delivers 8,000 BTUs, enough to cool a room up to 350 square feet, with an EER of 12.0. The unit has 3 fan speeds and 2-way slanted louvers that direct airflow in an upward, circular motion for even cooling. You can create a custom 24-hour schedule or control the unit remotely with the Frigidaire app for iOS and Android or dedicated remote control. If the power goes out, the unit will automatically restart when power is restored.  It has an air ionizer to help remove allergens, like pollen, and other impurities from the air and the magnetic front grill, which has an antibacterial filter, easily detaches for cleaning.

Installing and operating your room air conditioner

A little planning before installing your air conditioner will save you money and energy. The unit should be level when installed, so that the inside drainage system and other mechanisms operate efficiently. If possible, install the unit in a shaded spot on your home’s north or east side. Direct sunshine on the unit’s outdoor heat exchanger decreases efficiency by as much as 10%. You can plant trees and shrubs to shade the air conditioner, but do not block the airflow.

Don’t place lamps or televisions near your air-conditioner’s thermostat. The thermostat senses heat from these appliances, which can cause the air conditioner to run longer than necessary.

Set your air conditioner’s thermostat as high as is comfortably possible in the summer. The less difference between the indoor and outdoor temperatures, the lower your overall cooling bill will be. Don’t set your thermostat at a colder setting than normal when you turn on your air conditioner; it will not cool your home any faster and could result in excessive cooling and unnecessary expense.

Set the fan speed on high, except on very humid days. When humidity is high, set the fan speed on low for more comfort. The low speed on humid days will cool your home better and will remove more moisture from the air because of slower air movement through the cooling equipment.

Also, consider using an interior fan in conjunction with your window air conditioner to spread the cooled air more effectively through your home without greatly increasing electricity use. We like the Haiku Home L Series 52-inch Indoor/Outdoor Wi-Fi Enabled fan ($475 on Amazon), which provides coverage for indoor or outdoor space of up to 15 by 15 feet. It has a built-in LED light (40-watt equivalent) with 16 brightness settings. And, because it’s WiFi enabled, you can use your smartphone or Amazon’s Alexa for control.

Air Conditioner Cooling Needs Calculator

To determine the correct size Air Conditioner for your room, follow these easy steps:

1. Determine the square footage of the area to be cooled.
2. Using the square footage and the chart below, determine the correct cooling capacity. Cooling capacity is measured in British thermal units (BTUs) per hour.
3. Make any adjustments for the following circumstances:

• If the room is heavily shaded, reduce capacity by 10 percent.
• If the room is very sunny, increase capacity by 10 percent.
• If more than two people regularly occupy the room, add 600 BTUs for each additional person.
• If the unit is used in a kitchen, increase capacity by 4,000 BTUs.
• For the purpose of this chart, rooms that are connected by permanently open entryways wider than five feet ought to be considered as one room and their square footage should be combined.

Area to be Cooled (Square Feet)	Capacity Needed (BTUs per Hour)
100 to 150	5,000
150 to 250	6,000
250 to 300	7,000
300 to 350	8,000
350 to 400	9,000
400 to 450	10,000
450 to 550	12,000
550 to 700	14,000
700 to 1000	18,000
1000 to 1200	21,000

Source: http://www.techlicious.com/how-to/select-the-right-room-air-conditioner/

HVAC Repair & Troubleshooting Tips (P.4)

AIR CIRCULATION

The most important factor in efficient furnace operation is air circulation to ensure proper air circulation.

Furnace filter

The furnace filter should be checked monthly and replaced as needed. There are several types of filters available and range from one to five inches thick. The filter can be installed into the slot in the return or in an air cleaner. Air conditioning AC HVAC service in Sugar Land Texas, and Same day Air conditioning AC HVAC service in Missouri city Texas

Electronic filter

Some homes will have an electronic air filter which is powered by the furnace control board. When the circulation blower fan turns on mounted near the heat exchanger is a safety limit switch that monitors the air temperature. If the filter is clogged or the circulation blower fan motor fails the heat exchanger will overheat. The limits which will open and the control board will shut off voltage to the gas valve to prevent damage to the furnace.

Blower fan motor

The blower fan motor can run at multiple speeds to improve efficiency. Lower speeds are used when the furnaces-heating and higher speeds are used for air conditioning.  A noisy furnace is often the result of the draft inducer motor wearing out. If the circulation blower fan is causing the noise, the set screw on the blower wheel may have loosened causing the wheel to wobble on the motor shaft, you can fix this problem by tightening or replacing the screw or replacing the blower wheel altogether.  

<< https://heatingairconditioningintexas.wordpress.com/2017/03/23/how-to-troubleshoot-hvac-problems-and-malfunctions/

How to Troubleshoot HVAC Problems and Malfunctions

To diagnose heating, ventilation and air conditioning problems, start with the easy, visible items and work your way to the hidden components. An HVAC consists of a furnace, an air conditioner, ductwork and a fan connected to the ductwork. The thermostat controls these elements by signaling them to turn on or off based on programmed settings. As part of the ventilation system, a filter sits inside the cold air return that removes contaminants from the air before heated or cooled air is distributed throughout the home.

http://acscomfort.com

Diagnosis

Begin your diagnosis of the HVAC system by verifying that it has power. Locate the service panel and ensure the circuit breaker has not tripped. The furnace and the air-conditioner each have their own dedicated circuit breaker or fuse. Turn the circuit breaker off for the unit that is malfunctioning. Wait about 10 seconds and switch it back on. If you have fuses instead of circuit breakers, switch the main power off. Remove and replace blown, burnt or broken fuses. Next check the thermostat for power. Some thermostats receive power via the electrical system, while others contain batteries. Remove and replace batteries for battery-powered thermostats if there is no power at the unit.

Furnace

Switch the thermostat to “heat” mode and set the thermostat 3 to 5 degrees above the room temperature. Wait at least 30 seconds before checking for heat at an open register. If no heat comes out, turn the thermostat off. Confirm that the panel door on the furnace is closed. A switch inside the panel door allows the system to operate when it is fully engaged. If not engaged, the heater won’t come on. Reset the furnace by opening the panel door and turning off the gas or pushing the reset button. Wait five minutes — or follow the instructions in the unit’s manual for reset — then turn the gas back on.

Air Conditioner

Set the thermostat to “cool” mode. Adjust the thermostat setting 3 to 5 degrees below the room temperature. Locate an open register and check for cool air after waiting for 30 seconds. Reset the air conditioner at the circuit breaker. If the air conditioner was running, but stopped producing cold air, check the air conditioner for water below the unit. If there is water, dirty coils can cause the coils to freeze. Turn the air conditioner off at the thermostat and circuit breaker, let the unit sit for three hours, then clean the coils and restart the unit.

Ventilation

Ensure the fan is on at the thermostat and the registers are open. Newer thermostats have two settings for the fan: “on” and “auto.” When set to “on” the fan will run continually. When set to “auto” the fan kicks on with the heater or air conditioner calls for it. Locate the cold air return and remove the filter. Examine the filter for dirt. Cold air return filters must be clean for the system to operate efficiently. If your filter is a permanent one that requires cleaning, follow the steps in the owner’s manual. Locate the arrow on one side of the filter that shows the direction the air flows. After cleaning, ensure that you put the filter back with the arrow pointing toward the ductwork inside. Replace the disposable filter with a new one. If the registers for the ventilation system do not deliver air, locate the blower motor and check the belt for cracks or breaks.

Source: http://homeguides.sfgate.com/troubleshoot-hvac-problems-malfunctions-38873.html

<< https://heatingairconditioningintexas.wordpress.com/2017/03/20/hvac-repair-troubleshooting-tips-p-3/

HVAC Repair & Troubleshooting Tips (P.3)

Click to see the previous article: HVAC Repair & Troubleshooting Tips (P.2)

COMBUSTION

After a set period of time the control board since 24 volts to the gas valve opening it and allowing gas to flow over the igniter establishing a flame.

Flame sensor

Once the gases ignited a flame sensor detects whether or not a flame is present. If the burners don’t light or won’t stay lit the flame sensor may need to be cleaned with a fine abrasive pad to ensure it can detect the flame or the Air conditioning AC HVAC service in Sugar Land Texas sensor may need to be replaced.  

Flame rollout limit switches

Mounted on the burners are one or more flame rollout limit switches that ensure the flame is drawn through the burners, if the inducer fan motor can’t draw enough air through the burners, the rollout limits which will open and the control board will shut off the voltage to the gas valve. If the furnace is located in a closet or another cramped area, the limited available air may prevent the combustion process from the working properly. Closet doors will need to be louvered or space left at the bottom of the door to ensure proper airflow. Once the combustion process is complete the control board will send 120 volts to the circulation blower fan motor. The Fast Air conditioning AC HVAC service in Richmond Texas blower fan draws air through the return vent blows it pass the heat exchanger and forces it through the homes venting, overtime heat exchangers may crack and cause carbon monoxide to leak into the air being circulated throughout the home. Since carbon monoxide poisoning can result in death, we recommend that only experienced professionals repair or replace damaged heat exchangers. Under normal working conditions, the furnace will exhaust the carbon monoxide through a flu or exhaust pipe to the outside of the home. If the flu or pipe breaks, cracks or rush carbon monoxide will contaminate the air. To help keeping   v you safe,  a carbon monoxide detector should be installed near the bedrooms of your home and its batteries checked regularly. If a leak is detected, the furnace should be shut off immediately. Condensation often builds up in the exhaust pipe of high efficiency furnace. For this reason, a condensate pump or floor drain is needed

Contact us:  http://acscomfort.com/contact

 

HVAC Repair & Troubleshooting Tips (P.2)

Click to see the previous article: HVAC Repair & Troubleshooting Tips (P.1)

TEMPERATURE CONTROL

The temperature and the home is regulated the by wall thermostat. The thermostat can be powered by the furnace control board or by batteries. The thermostat must be in central location in the home position at eye level and away from direct sunlight for proper temperature regulation. When the thermostat detects this decrease in temperature it switches on the heat circuit and the furnace control board begins the ignition process, Same day Air conditioning AC HVAC service in Pearland TexasSame day Air conditioning AC HVAC service in Pearland Texas.

IGNITION

When the furnaces residential power switch is turned on and heat is needed the furnace goes through a timed ignition sequence. The sequence begins with the control board sending 120 volts of alternating current to the draft inducer fan motor.

Draft inducer fan motor

The inducer fan motor draws air into the burner assembly which maybe the air surrounding the furnace or fresh outside air supplied by a pipe.

Vacuum Switch

Once the fan reaches its maximum speed a vacuum switch is closed which ensures that gas will not enter the furnace. Unless the toxic fumes can be exhausted, if the inducer motor doesn’t turn on of run too slow, The vacuum switch will not close and the ignition sequence will stall. Once the vacuum switch closes 24 volts with travel through the switch and one or more limit switches allowing control board to continue the startup. The control board now sends 120 volts to a globe our style igniter depending on the model. A defective igniter will halt the ignition sequence and prevent the furnace from heating. If you experience this problem, a globe our style igniter can be tested for continuity to help determine if the part is functioning or not. Be aware that some models will use a spark igniter instead Emergency air conditioning service in Katy.

Spark igniters

Spark igniters will also receive voltage from the control board, but the amount of voltage is greatly increased and will pulse to create the spark.

Visit our website at here

How to get the effective Heating System

When your home heating property is really costly, Fast Air conditioning AC HVAC service in Richmond Texas and Air conditioning AC HVAC service in Richmond Texas in that case assure for your requirements stick to some of our these pointers to find the preferred out of your heat together with get inexpensive ones expense:

As soon as picking out a suitable unit process, notice the Energy Star label and Energy Factor rating. The higher EF is most effective, nevertheless remember that’s correct when you compare the same type of unit.

Check doors and windows to fix the gaps and holes which will permit heating to escape and your house be drafty and uncomfortable.

Visit our website at: http://acscomfort.com/services/heating-repair

Take into consideration updating your old home’s windows using energy-efficient home’s windows. A lot of these home’s windows are generally very far cost effective, since verified from your reduced cooling and heating expense.

The 20 years aged heating system should be considered. Current designs may well save on home heating bills just by 15 to 25 %.

Heating that bedrooms people recurrent probably the most. You can save by not necessarily warming up the bedroom during the day but rather heating the living room and kitchen better from 3-9 PM when that’s the place your family members gets to spend the majority of time.

Have a HVAC professional check up on your heating system to schedule an in-home free checking and free consultant service for your heating system such as ACS Absolute Comfort heating and cooling service enterprise.

> Other article: HVAC Repair & Troubleshooting Tips (P.1)

Ping submission 2/22

HVAC Repair & Troubleshooting Tips (P.1)

Although furnaces can differ from model to model, they operate on similar principles. Today, we will address how furnace works as well as potential problems you may encounter. The heating capacity of the furnace is measured using a British Thermal Unit or BTU. Most furnaces are rated between 40,000 and 130,000 BTU. Forced air furnaces can be installed to send heated air up down or sideways to accommodate the space in which the furnaces to be installed.

Click here to visit our website or via the link: http://acscomfort.com/local/sugar-land-tx

Gas burners

Gas burners fueled by either natural gas or propane are used to generate the heat. Modern gas furnaces have two separate airflow systems which operate while the furnace is running.

Draft inducer fan motor

The first system uses a draft inducer fan motor to draw air into the burner assembly. The air allows the burners to warm the heat exchanger, the air within the burner assembly is then exhausted to the outside of the home, which is necessary since this air contains toxic fumes such as carbon monoxide.

Blower fan motor

The second air system uses a blower fan to draw air through the return vent blow it pass the heat exchanger and force it through the homes venting. The room air is then drawn back through the return and the airflow cycle continues, Air conditioning AC HVAC service in Richmond Texas.

Thermostat

Once the room air has warm sufficiently the wall thermostat signals the furnace to turn off until the room temperature decreases. This process can be broken down into four main factors: temperature control, ignition, combustion and air circulation.

> Simple ways to lower your energy bills – KEEP YOUR HOME WARM

Simple ways to lower your energy bills – KEEP YOUR HOME WARM

Finding ways to cut your energy bills doesn’t have to be complicated. In fact, it’s the simple choices we make that can have a biggest impact. There are a few ways that you can help your heating run better and save you money in the winter months.

KEEP YOUR HOME WARM

Windows and Doors

– Using heavy and thick curtains to stop heat escaping from your windows. The best one is fitted close to the window, wide enough to overlap the window frame and long enough to touch the floor.

– Installing pelmets at top of your windows. They do a great job of stopping cold air coming into your rooms.

– Using a double glazing to halve heat loss through windows, reduce external noise. It’s designed in most new houses, you should prioritize to install double glazing to the main heated areas of the house as well as to large windows.

Visit us: http://acscomfort.com/local/katy-tx

Cover windows and patio doors with plastic film

– Covering the windows and sliding patio doors with clear plastic film can reduce that loss. The transparent film is inexpensive, but that windows account for 25 percent of heat loss in homes.

Heat your home by sunlight

Open curtains during the day to allow sunlight to heat your home and close them at night. Although the sun’s heat is ample and free, harnessing it to warm your home isn’t a simple process. It takes a little work—and creativity. With those two ingredients, though, you can use the sun to warm your home once the cold days settle in.

Close of any rooms that is not in use

If your heating system will let you, turn it off in empty rooms, why waste energy heating areas that you’re not using? Air conditioning AC HVAC service in Sugar Land Texas

 

> Tips save energy on heating system

Tips save energy on heating system

Heating is the largest energy expense, about 35-50% of annual energy bills in your home. How much energy your heating system depends on 4 factors:

Location

Living in cold climates in the US is more energy demanding than living in warmer climates because the house will lose more heat, Emergency air conditioning service in Richmond.

visit us at: http://acscomfort.com

How big your house is

As you know a bigger the house, the more energy it will take to heat it.

The energy efficiency of the house

All heaters produce air movement as the hot air rises from the heater to the ceiling. Then the hot air is cooled when in contact with windows, walls and ceiling. To minimise losing heat by using heavy curtains with snug pelmets. Always consider to appropriate clothing to stay warm.

Also, improving insulation, sealing air leaks, and repairing the heat distribution system are excellent opportunities to save energy.

In addition, install appropriate position for your heater and furniture to deflect and avoid draughts.

How energy efficient the heating system is

A correctly sized heater is very important. You will waste money on buying a bigger heater than you need and waste energy in operating it. For Emergency air conditioning service in Katy

>> More articles: Ceiling Fans: A Must in Summertime if You Want to Save

 

Ceiling Fans: A Must in Summertime if You Want to Save

Summers in the Houston area Katy, Sugar Land, Pearland, Richmond and Missouri city are sometimes scorching hot.  That means turning on the air conditioner more often to keep your home feeling comfortable. But that also means an increase in energy expenses. One effective way to curb some of these cooling costs is by using ceiling fans.

Ceiling fans make you feel comfortable when it’s hot by blowing air over your body and increasing the evaporation, which is how the body cools itself. You feel the reaction just like a wind chill factor.

Following or site

Ceiling fan makers continue to improve designs and features to make these energy- saving tools more appealing and quieter. If you want to save money and stay cool this summer, here’s what you need to know about ceiling fans:

• They can help keep you warm
• They keep room temperature constant
• Size matters
• Play the angles
• They work with your central air

For more tips on using ceiling fans or Air conditioning AC HVAC service in Pearland Texas, please contact us at ACS Absolute Comfort – phone number 281-495-2013 anytime.

More: https://heatingairconditioningintexas.wordpress.com/2017/01/11/cleaning-air-filter/

Cleaning Air Filter

The purpose of an air filter is to collect all of the dirt, dust, debris and control or eliminate pollutants in the breathable air and air processed by house systems such as Air conditioning A/C HVAC. The air filter in your home is meant to clean the air as it passes through, making the air you breathe cleaner. However, it is an an oft-overlooked component.

More information

If you have a reusable air filter, cleaning it is actually quite simple. Cleaning it is one of the easiest and most important steps you can take to protect your heating and cooling system.
Steps to take:
Step 1: Open the vent. Vents Usually have a screw to remove or a simple latch to allows the vent to swing open.
Step 2: Remove the air filter.
Step 3: Take the filter outside and brush dirt, dust and debris
Step 4: Turn the vacuum on use the hose to suction remaining loose material from the filter.
Step 5: Wash the filter with running water. The water should flow in the opposite direction of the airflow
Step 6: Dry the filter with paper towels, and then put it outdoors to air dry.
Step 7: Use the vacuum attachments to clean the vent and vent frame
Step 8: Once the filter is completely dry, seat the filter back in place. Make sure the airflow arrows face the right direction.
Step 9: Close and secure the vent

If you would prefer to have all your AC and HVAC service taken care by a professional instead, you can request an Emergency air conditioning service in Pearland by either calling ACS Absolute Comfort at 281-495-2013. This company provides services in Sugar Land, Katy, Richmond, Pearland, and Missouri City areas.

Air conditioning AC HVAC service in Missouri city Texas  |

>> How to clean air ducts (P2)

How to clean air ducts (P2)

I am going to tell your how to clean air ducts yourself to , instead of calling a professional contractor. Follow these steps to clean air ducts:

• Make sure you replaced old furnace filter, so that the dust doesn’t end up getting pulled into the fan motor.
• Cover supply air registers with paper to avoid dust from drifting into the rooms as you work.
• Don’t only shut the fan off at the thermostat or furnace via the switch or breaker panel, but also turning the power off to prevent electric shock or allow air to pass through the ductwork without being filtered.
• Remove the panels on the front of the furnace and access the blower compartment, use the vacuum to sweep up the dust in the blower compartment and return air boot. The great bulk of dust will be here. So that you should clean the furnace fan as well.
• Replace furnace filter to cut down the dust in your home. The purpose of an air filter is to collect all of the dirt, dust, debris and control or eliminate pollutants in the breathable air and air processed by house systems.
• Air conditioning AC HVAC service in Katy Texas

• Click here

>> How to clean air ducts (P1)

> Simple ways to lower your energy bills – Save on Air conditioning

 

How to clean air ducts (P1)

Most people are now aware that indoor air pollution is an issue of growing concern and increased visibility, so cleaning air ducts in your house is necessary. When ducts are clean, the heating system lasts longer- because dirty ducts will reduce effect of your HVAC system. Dust mite debris detrimental effect on your health and cause allergic reactions, for those of us with allergies, cleaning air ducts should be a welcome improvement.

Emergency air conditioning service in Pearland 

The ductworks in your heating and cooling system is the air distribution network that sends conditioned air throughout your home. This system is a large pipes, so it can accumulate dust, mold and debris. We dust less often, and the air we breathe at home is cleaner. I am going to tell your how to clean air ducts yourself to save money, instead of calling a professional contractor.

Emergency air conditioning service in Richmond

Things You Need to Clean Your Air Ducts:

• Furnace Filter

• Vacuum

• Brush

• Screwdriver or Hex Driver

• Paper Towels

Following the next topic for air duct cleaning steps.

https://heatingairconditioningintexas.wordpress.com/2016/09/19/5-tips-for-buying-a-central-air-conditioning/

Reference: dengarden.com/home-improvement/how-to-clean-ventilation-ducts

Simple ways to lower your energy bills – Save on Air conditioning

Energy Star

If you are buying a AC, look for the ENERGY STAR label is a simple way to keep the cost of energy expenses within a reasonable range and protect the environment. With a Energy Star, it will use about 14% less energy than minimum government standards, and a room air conditioner will save at least 10%. Emergency air conditioning service in Richmond

Maintenance Air conditioner

Most A/C manufacturers recommend yearly maintenance Emergency air conditioning service in Missouri city. Failure to maintain your unit may void the warranty. Ask your contractor for details. Consider an AC / HVAC maintenance contract with a trusted contractor to head off potential A/C problems before they become serious. A professional should be able to diagnose any inefficiencies before you’ve wasted money on monthly heating and cooling bills.

Cleaning air filter

Air conditioning AC HVAC service in Missouri city Texas A dirty filter will reduce your AC’s efficiency, making it use more energy. Clean air filter monthly and expect to change the filter every three months.

Appropriate air conditioning capacity

Cooling one room with a split air conditioning unit  requires less energy than a central air conditioning for whole house. when you choose inadequate air conditioning capacity compared to volume or area of the room, the room temperature is not enough cold, it would force the air conditioning has to work constantly, resulting in energy consumption, fast warm-up and the broken machine.

Fast Air conditioning AC HVAC service in Richmond Texas

Using thermostat for Air Conditioners

Use a programmable thermostat to automatically adjust the set temperature during the day for your central air conditioning. Set up temperature at different times of the day and night for the thermostat, then it does the work and help you reduce to $150 a year in energy bills.

>> Simple ways to lower your energy bills – Saving on lighting

>> Simple ways to lower your energy bills – Save on water heating

>> Simple ways to lower your energy bills – Save on other appliances and electronics

Simple ways to lower your energy bills – Save on other appliances and electronics

Standby power

Many appliances have a Air conditioning AC HVAC service in Sugar Land Texas standby mode during which they are not providing useful output but still consume energy, they cost you $100 a year on your power bills. At times, we encounter situations where doing the same is either a hassle or is difficult. Plug them all into multi-plug boards so you can switch them all off at once and buy low energy standby appliances- it’s getting easier. Or set up a “Time Switches” is needed.  

Set up timers for appliances

Several appliances consume electricity if they aren’t switched off from the mains. This is in a lot of power wastage. Set up the appliances which you know that certain them will not be used during specific time of the day on time switches to save electricity. Fast Air conditioning AC HVAC service in Pearland Texas.

Set up timers for Air Conditioners

Almost us use AC at night, switch it off after a few hours of use, however, an air conditioner consumes a lot of power and getting up in the middle of the night is a hassle. Set up a timer to switch on AC for Emergency air conditioning service in Katy 20 mins and switches off for 40 mins. This can keep the room comfortable for 20 mins of cooling and for the rest 40 mins. This helps reduce power consumption significantly.  

Set up timers for lights

It is observed that people often tend to eliminate switching off the lights and other appliances where they use power without responsible for paying for it. Air conditioning AC HVAC service in Richmond Texas Or the house needs lighting only between 6AM and 6PM a day, sometimes we can forget to switch off lights and they are even left on 24 hours throughout day or week. In such cases, a timer is quite helpful.

> Others: Simple ways to lower your energy bills – Save on water heating

>> Simple ways to lower your energy bills – Saving on lighting

Simple ways to lower your energy bills – Save on water heating

• Install an inexpensive shower flow restrictor. Reducing the flow rate by 1 litre per minute could save a household of three around $80 per year.

<< Simple ways to lower your energy bills – Saving on lighting

• Aerators are inexpensive to replace and they can be one of the most cost-effective Fast Air conditioning AC HVAC service in Missouri city Texas  water conservation measures. For maximum water efficiency, purchase aerators that have flow rates of no more than 1.0 gpm. Some aerators even come with shut-off valves that allow you to stop the flow of water without affecting the temperature.

• Using dishwasher efficiently, one feature that makes a dishwasher more energy efficient is a booster heater. Air conditioning AC HVAC service in Sugar Land Texas A booster heater increases the temperature of the water entering it to the 140ºF for cleaning. Dishwasher with booster heaters typically cost more,  but they pay for themselves with energy savings in about 1 year. In addition, you should check the EnergyGuide label before purchasing a new dishwasher. Dishwashers come in three different sizes: full-sized, slimline and compact. Each size has a range of capacities to choose between depended on several different factors, such as size of household and amount of dishes used per day. http://acscomfort.com/services/ac-tune-up

• Maintain your hot water system regularly to keep your water heater running efficiently and reliably. Maintenance should start with a furnace tune-up by a service technician such as service technician of ACS Absolute Comfort (phone number 281-495-2013). We will inspect and clean the combustion chamber and the fuel nozzle and run a combustion test.

Water heating | Image source: energy.gov

Simple ways to lower your energy bills – Saving on lighting

–  Turn off lights in areas not being used. You’ll save electricity every time you turn the lights off. You might worry that Air conditioning AC HVAC service in Sugar Land Texas you wear out the lights quicker by turning them on and off. However, it’s not worth worrying about, that effect is so small. You can safely turn your lights off every time you leave the room, no matter how short the off duration.

–  Open curtains and blinds during daylight hours, rather than turning on the light to make the most of natural light. Daylighting is the use of windows and skylights for your home.

–  Replace your home’s incandescent light bulbs with Compact Fluorescent Lamp(CFL) or Light Emitting Diode(LED) bulbs. You’ll save energy with the lower wattage it takes to power the bulb but also from reduced cooling costs-incandescent bulbs give off 90 percent of their energy as heat. Use fluorescent tubes, they use a quarter of the electricity consumed by ordinary bulbs and last around eight times longer.

>> More: Cost-Effective Heating and Cooling service

–  In addition to turning off your lights manually, you may want to consider using sensors, timers, and other automatic lighting controls. They provide convenience by turning lights on automatically when someone enters a room, and save energy by turning lights off soon after the last occupant has left the room. Emergency air conditioning service in Katy Occupancy sensors must be located where they will detect occupants or occupant activity in all parts of the room. Timers can be used to turn on and off outdoor and indoor lights at specific times. There are two types of timers: manual timers, which plug into an electrical outlet for controlling objects such as lamps or light strings; and in-wall programmable digital timers (which look like digital thermostats), which automate indoor or outdoor lighting; Fast Air conditioning AC HVAC service in Pearland Texas .

Carbon Monoxide Poisoning Increase in the Winter

Fast Air conditioning AC HVAC service in Katy Texas. “While carbon monoxide poisoning is a year-round threat, it’s more common in cold weather when people are seeking ways to keep warm by using space heaters inside.” , said Stephen May, MD, medical director for the TDH Emergency Preparedness Program.

With winter here, most people are closing their windows and turning up the heat. These actions increase the risk of poisoning by carbon monoxide, a “silent killer” – carbon monoxide is an odorless, colorless and tasteless gas that causes more than 400 deaths and 20,000 visits to hospital emergency rooms in the U.S. each year. For more information, please click here

Symptom severity is related to both the CO level and the duration of exposure. Prolonged exposure can lead to other symptoms such as vomiting, chest pain and confusion, serious medical problems and even death. Same day Air conditioning AC HVAC service in Katy Texas Poisonings from carbon monoxide are especially common during cold weather spells, as families increase the use of gas, oil and coal burning appliances.

>> Carbon Monoxide Poisoning: What You Should Know

Cost-Effective Heating and Cooling service

Utilizing the services of the Fast Air conditioning AC HVAC service in Katy Texas gives you the opportunity to  keep you comfortable.

Customer satisfaction is the heart of our business. When you select us as your air conditioning provider, you have peace of mind knowing we are there to handle your every need. 

ACS Absolute Comfort is a trusted heating and cooling service in Houston Texas and the surrounding area such as Katy, Sugar Land, Richmond, Pearland and Missouri, Texas. Call us at 281-495-2013 for Same day Air conditioning AC HVAC service in Missouri city Texas.

We are a full-service air conditioning and HVAC company and deliver heating and AC solutions for a variety of situations:

•    Commercial and residential
•    New construction and remodeling projects
•    Replacement, retrofit and upgrade systems
•    Indoor air quality solutions

We realize money is tight, and we constantly search for ways to ease the financial anxiety often associated with purchasing and maintaining your heating and cooling system. That is why we offer various specials on new AC installation and AC repair services throughout the year Fast Air conditioning AC HVAC service in Richmond Texas.

https://heatingairconditioningintexas.wordpress.com/2016/08/29/be-careful-while-using-air-conditioning-in-summer/

Carbon Monoxide Poisoning: What You Should Know

Carbon monoxide (CO) is an odorless, colorless gas formed by the incomplete combustion of fuels. When people are exposed to CO gas, the CO molecules will displace the oxygen in their bodies and lead to poisoning.

 

CO is produced by appliances and gas burning Fast Air conditioning AC HVAC service in Richmond Texas that generate combustion. For example, gas, propane and wood are commonly used fossil fuels. The danger occurs when excessive CO accumulates in a poorly ventilated space or due to a faulty appliance.

 

CO is often called the “silent killer” because people will ignore early signs and eventually lose consciousness and be unable to escape to safety. CO poisoning is especially dangerous for people who are sleeping or intoxicated. The sleeping person may die without ever waking.

Symptoms Signs and symptoms of carbon monoxide poisoning

• Blurred vision
• Chest pain
• Confusion
• Dizziness
• Headache
• Loss of consciousness
• Nausea
• Shortness of breath
• Vomiting
• Weakness

Emergency air conditioning service in Richmond

Difference between CO poisoning and the flu symptom

• You feel better when you are away from home
• Everyone is the home is sick at the same time while the flu is typically passed from person to person
• The family members most affected spend the most time in the house
• Indoor pets appear ill
• You don’t have a fever or body aches, and you don’t have swollen lymph nodes that are common with the flu and some other infections
• Symptoms appear or seem to get worse when using fuel-burning equipment

 

Carbon Monoxide Sources in the Home

• Furnaces or boilers
• Gas stoves and ovens
• Fireplaces, both gas and wood burning
• Water heaters
• Clothes dryers
• Wood stoves
• Power generators
• Motor vehicles
• Power tools and lawn equipment
• Tobacco smoke

Prevention

The precautions to prevent CO poisoning are simple. Protect yourself and family by heeding the following advice:

• Install carbon monoxide detectors

– Install a carbon monoxide detector in the hallway near each sleeping area in your house, and one on each floor

– Check the batteries in conjunction with your smoke detector inspections and change the batteries at least twice a year.

– If the alarm sounds, evacuate all members of the household and call 911.

– Some experts recommend installing a CO detector near the furnace portion of the heating and central air conditioning system. Fast Air conditioning AC HVAC service in Katy Texas.

• Open the garage door

If you have an attached garage, keep the garage door open and the door to the house firmly closed while the car is running.

• Use gas appliances as recommended

Use fuel-burning indoor space heaters only when doors or windows are open to provide fresh air and monitor them when in use. Don’t run a generator in an enclosed space, such as the basement, garage or inside of the home!

• Maintain gas appliances and the fireplace

– Ensure your gas appliances are properly vented.

– Inspect the vent pipes periodically to ensure they aren’t blocked by debris or bird nests.

– Have your fireplace chimney and flue professionally cleaned every year.

– Schedule inspections for all gas appliances by a professional repairman.

For more information on avoiding carbon monoxide poisoning, contact ACS Absolute Comfort at 281-495-2013. We’ve provided top-notch HVAC services for Houston-area homeowners since 2007. Same day Air conditioning AC HVAC service in Pearland Texas

 

5 tips for buying a central air conditioning

“An air conditioner is like a shoe, it has to fit,” said Michael Brief, national field sales manager for air conditioner manufacturer Friedrich.
An Air conditioner not only helps to circulate cool air, reduce humidity and maximize comfort, but also helps filter out harmful bacteria, allergy-causing agents, dirt … in the air . A typical central A/C system can last anywhere from 10 to 20 years, so most homeowners will have to purchase a new system at some point in their lives.
While you’re looking for Fast Air conditioning AC HVAC service in Pearland, Katy, Sugar Land, Richmond or Missouri City Texas, home, take a look at these tips to make the process a little easier to navigate.

Which type of air conditioner should I buy?
There are two main types of air conditioner: single-unit models that are portable and need to be vented through a window or door, and split-unit models that are permanently fixed to a wall,  Air conditioning AC HVAC service in Richmond Texas

A/C unit size
Most people believe that the bigger is better, it will cool your home swiftly. It’s not simple. A system that’s too big will switch on and off more often, raising your energy costs while not dehumidifying properly and reducing energy efficiency.
Air conditioners come in various shapes and sizes, but are often described in terms of their BTU (British thermal unit) output. As a general rule, 5,000 to 8,000 BTUs is adequate for most living rooms or bedrooms. For rooms that regularly contains more than 2 people add an additional 600 BTU’s per person.

Fast AC service in Katy
Energy Efficiency
All air conditioning units are labeled with their EER (Energy Efficiency Rating). Units with higher ratings offer lower greenhouse emissions and monthly electric bills.

EERs range from 8 to 11.5. The Home Depot carries several models that are Energy Star rated. Check the yellow Energy Guide label on new air conditioners for more information.
Any air conditioner you buy to replace an old unit will be more energy efficient. When you replace a central air conditioner, make sure both the condenser and the air handler are replaced at the same time. The two components were made to work together. If you change one and not the other, your system may become inefficient.

Consider Cost
Think of how efficient the system is and how much you’ll save on your energy costs each month and year. Additionally, consider the added value to your home if you plan to sell. Updating and adding new ductwork may be a big expense, but giving your home a good central air conditioner that’s effective and efficient can be a big selling point.

Emergency air conditioning service in Richmond
Air conditioner maintenance
Most A/C manufacturers recommend yearly maintenance. Although most air conditioning units can run on their own for extended periods of time, they will eventually need to undergo maintenance in order to operate at maximum efficiency throughout the entire year. To make sure that your AC unit will continue to function efficiently, make sure you have it checked at least once per cooling season.

For more advice about what to consider when buying an AC HVAC system, please feel free to contact ACS Absolute Comfort at 281-495-2013.

Be careful while using Air Conditioning in summer

Air Conditioning AC HVAC Repair & Installation in Houston Texas

You just need a question answered or air conditioning AC HVAC installation or repair service, contact us. Our technicians are more than happy assist you

ACS Absolute Comfort has been a leader among Air conditioning AC HVAC contractors.
We deliver heating and Same day Air conditioning AC HVAC service in Sugar Land, Katy, Richmond, Pearland, and Missouri City, Texas

 

Be careful while using Air Conditioning in summer

Sultry hot weather makes us just like to stay in air-conditioned room. However, you should be careful if using air conditioning during the hot season to avoid thermal shock, causing harm to the health of the entire family.

Summer indoor and outdoor temperature difference is relatively large

Using Air conditioning AC HVAC service in Richmond Texas, everybody usually wants cool rapidly, so you’ll probably set lowest temperature. However, when the temperature is too low and the outdoor temperature difference is too big, you will be susceptible to thermal shock and cold.

It is also recommended that you should set the thermostat to 78 degrees when you’re home and 85 degrees when away from home during the summer.  It is much more energy efficient that way since your air conditioner won’t have to run as long to cool your home upon your return.

Staying in air-conditioned rooms constantly

In sultry hot weather, air-conditioned rooms is really paradise, however, you shouldn’t stay in over 8 hours constantly. It causes respiratory diseases such as cold,  runny nose, nasal congestion, fever, headache, or cutaneous pigmentation such as dry skin, allergies, especially when using the air conditioning not cleaned periodically.

Fast AC service in Katy

Closed air-conditioned room always

If the air-conditioned room without ventilation holes, ventilation fans, the air in the room is susceptible to infection, accumulation of CO2 if the air is not renewed.

Therefore, you should open door to get a fresh air outside every 1-2 hours or you can install a ventilation fans to refresh room without opening the door.

Into air-conditioned room  after returning from hot outside

Once returning from hot outside or sport …you shouldn’t be into air-conditioned room immediately to your body temperature down. If you enter the air-conditioned room unexpectedly, you will be susceptible to get cold because the body couldn’t adapt to cold air. Moreover, when under the sun or exercise, the blood vessels will dilate, so if entering the cold room immediately, it causes the sudden contraction of blood vessels and you may get stroke.

You should also take advantage of integrated pleasant breeze on the air conditioning, but prevent cold air blowing directly on skin, helping to bring the ool and comfortable air.

Emergency air conditioning service in Richmond

Not clean air conditioning periodically

Air conditioner not only provides a cool air, but also helps filter out harmful bacteria, allergy-causing agents, dirt … in the air. Therefore, air conditioning maintenance is necessary, it helps clean AC, since harmful bacteria, allergy-causing agents, dirt… accumulate in the indoor unit will not have a chance to multiply and spread in the air, helping your entire family avoids respiratory diseases. Furthermore,  air conditioning maintenance periodically will help air conditioning operate more durable.
If your are in the  Katy, Sugar Land, Pearland, Richmond and Missouri City areas, call ACS Absolute Comfort at 281-495-2013 to ask about an affordable Same day Air conditioning AC HVAC service in Missouri City yearly maintenance contract.